Universal-air-tools UT5761 User Manual download pdf

Important

Read these instructions carefully before installing, operating,

servicing or repairing this tool. Keep these instructions in a safe

accessible place.

Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,

Dismantling, Assembly and Safety Rules

Operator Instructions

Manufacturer/Supplier Product Type

RPM

Cycles Per Min

Model No/Nos Serial No

Product Nett Weight

lbs

Recommended Use Of

Balancer Or Support

Recommended Hose Bore

Size - Minimum

Recommended Max.

Hose Length

Ins M/M Ft M

Page No 1

Extended Cut Off Tool

UT5761

3.96

1.8 3/8 10 30 10

16,000

Universal Air Tool Company Limited

Unit 8

Lane End Industrial Park

High Wycombe

Bucks

HP14 3BY

Work Stations

The tool should only be used as a hand held hand operated tool. It is

always recommended that the tool is used when standing on a solid

floor. It can be used in other positions but before any such use the

operator must be in a secure position having a firm grip and footing and

be aware of the safety rules to be

obeyed when using the grinder.

Foreseen Use of the Tool

This tool is designed to be used with flat reinforced resin 4 ins dia max.

discs having a speed rated above 16,000 rpm. The bore size of the disc

is 3/8 ins.

The tool should not be used with any other type or rating of abrasive disc

or wheel. It must never be used with saw blades or other cutting

devices.

Do not use the tool outside the design intent. Never modify the tool for

any other purpose, or for its use as a disc cutter without first seeking

advice from the manufacturer or an authorised representative.

Tel No

Fax No

(01494) 883300

(01494) 883237

Noise Level

Sound Pressure Level 84.0 dB(A)

Test Method

Tested in accordance with Pneurop

test code PN8NTC1 and ISO Standard 3744

Vibration Level

Test Method

Tested in accordance with ISO

standards 8662/1 & 8662/4

Less than 2.5

Putting Into Service

Air Supply

Use a clean lubricated air supply

that will give a measured air

pressure at the tool of 90 p.s.i./6.3

bar when the tool is running with

the trigger/lever fully depressed.

Use recommended hose size and

length. It is recommended that the tool is connected to the air supply as

shown in figure 1. Do not connect the tool to the air line system without

incorporating an easy to reach and operate air shut off valve. The air

supply should be lubricated. It is strongly recommended that an air filter,

regulator, lubricator (FRL) is used as shown in Figure 1 as this will supply

clean, lubricated air at the correct pressure to the tool. Details of such

equipment can be obtained from your supplier. If such equipment is not

used then the tool should be lubricated by shutting off the air supply to

the tool, depressurising the line by pressing the trigger on the tool.

Disconnect the air line and pour into the intake bushing a teaspoonful

(5ml) of a suitable pneumatic motor lubricating oil preferably

incorporating a rust inhibitor. Reconnect tool to air supply and run tool

slowly for a few seconds to allow air to circulate the oil. If tool is used

frequently lubricate on daily basis and if tool starts to slow or lose power.

It is recommended that the air pressure at the tool whilst the tool is

running is 90 p.s.i./6.3 bar.

Metres / Sec²

Personal Safety Equipment

Use - Safety Glasses

Yes

Use - Safety Gloves

Yes

Use - Safety Boots

Use - Breathing Masks

Yes

Use - Ear Protectors

Yes

Air Pressure

Recommended Working

6.3

bar

PSI

Recommended Minimum

n/a

bar

n/a

PSI

Maximum

7.0

bar

100

PSI

1 2 3 4

Summary of Contents

Page 1 - Cycles Per Min

ImportantRead these instructions carefully before installing, operating,servicing or repairing this tool. Keep these instructions in a safeaccessible

Page 2 - Reassembly

Page No 2Dismantling & Assembly InstructionsDisconnect tool from air supply.Grip connector pipe (29) and unscrew head (30). Grip head (30) inthe v

Page 3 - UT5761 Extended Cut Off Tool

UT5761 Extended Cut Off ToolPage No 3Dec 2007 Ver 1.00Ref No Part No Description1 5K-3011B01 Motor Housing2 30102 Spring Pin3 51-3011A03 Air Inlet4 6K

Page 4

AccessoriesDistributorNotesPage No 4Declaration of ConformityUniversal Air Tool Company LimitedUnit 8, Lane End Industrial Park, High Wycombe, Bucks,

Comments to this Manuals

No comments

Universal-air-tools UT5761 User Manual

Browse online or download User Manual for Tools Universal-air-tools UT5761. Universal Air Tools UT5761 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Universal-air-tools UT5761