Universal-air-tools UT5766 User Manual download pdf

Read these instructions carefully before installing, operating,

servicing or repairing this tool. Keep these instructions in a safe

accessible place.

Important

Operator Instructions

Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,

Dismantling, Assembly and Safety Rules

Manufacturer/Supplier Product Type

RPM

Cycles Per Min

Universal Air Tool Company Limited

Unit 8

Lane End Industrial Park

High Wycombe

Bucks

HP14 3BY

Tel No Fax No(01494) 883300 (01494) 883237

Model No/Nos Serial No

Product Nett Weight

lbs

Recommended Use Of

Balancer Or Support

Recommended Hose Bore

Size - Minimum

Recommended Max.

Hose Length

Ins M/M Ft M

Foreseen Use of the Tool

The tool is designed for the purpose of cleaning or sanding of materials

using a continuous abrasive belt. Belts are available in various grades to

suit fine finishing or fast material removal.

Do not use the tool for any other purpose than that for which it was

designed. Do not modify this tool for any other use or for its use as a belt

sander without first consulting the manufacturer or the manufacturer’s

authorised distributor.

Putting Into Service

Air Supply

Use a clean lubricated air supply that will

give a measured air pressure at the tool

of 90 p.s.i./6.3 bar when the tool is

running with the trigger fully depressed.

Use recommended hose size and

length. It is recommended that the tool

is connected to the air supply as shown

in figure 1. Do not connect the tool to

the air line system without incorporating

an easy to reach and operate air shut off

Work Stations

The tool should only be used as a hand held hand operated tool. It is

always recommended that the tool is used when standing on a solid

floor. It can be used in other positions but before any such use the

operator must be in a secure position having a firm grip and footing and

be aware of the safety rules to be obeyed when using the sander.

60mm Belt Sander

UT5766

7000

3/8 10 30 10

2.4

1.1

Page No 1

Noise Level Sound Pressure Level 86.8 dB(A)

Test Method Tested in accordance with Pneurop

test code PN8NTC1

Vibration Level

Test Method Tested in accordance with ISO

standard 8662

1.43

Metres / Sec²

Air Pressure

Recommended Working

6.3

bar

PSI

Recommended Minimum

n/a

bar

n/a

PSI

Maximum

7.0

bar

100

PSI

Personal Safety Equipment

Use - Safety Glasses

Yes

Use - Safety Gloves

Use - Safety Boots

Use - Breathing Masks

Yes

Use - Ear Protectors

valve. The air supply should be lubricated. It is strongly recommended

that an air filter, regulator, lubricator (FRL) is used as shown in Figure 1

as this will supply clean, lubricated air at the correct pressure to the tool.

Details of such equipment can be obtained from your supplier. If such

equipment is not used then the tool should be lubricated by shutting off

the air supply to the tool, depressurising the line by pressing the trigger

on the tool. Disconnect the air line and pour into the intake bushing a

teaspoonful (5ml) of a suitable pneumatic motor lubricating oil

preferably incorporating a rust inhibitor. Reconnect tool to air supply

and run tool slowly for a few seconds to allow air to circulate the oil. If

tool is used frequently lubricate on daily basis and if tool starts to slow or

lose power.

It is recommended that the air pressure at the tool whilst the tool is

running is 90 p.s.i./6.3 bar. The tool can run at lower and higher

pressures with the maximum permitted working air pressure of 100

p.s.i./7 bar.

1 2 3 4

Summary of Contents

Page 1 - Cycles Per Min

Read these instructions carefully before installing, operating,servicing or repairing this tool. Keep these instructions in a safeaccessible place.Imp

Page 2 - Tool Maintenance

OperatingSelect a suitable abrasive belt of the required grade. The belt size for thistool is 60 mm wide x 260 mm circumference (continuous belt) and

Page 3 - UT5766 60mm Belt Sander

UT5766 60mm Belt SanderPage No 3Jun 2012 Ver 1.00Ref No Part No Description1A UT5766-01A Motor Housing2 UT5766-02 Deflector3 UT5766-03 Tap Screw (

Page 4

DistributorNotesPage No 4This document may not be copied wholly or in part by anyone without the consent of the Directors of Universal Air Tool Compan

Comments to this Manuals

No comments

Universal-air-tools UT5766 User Manual

Browse online or download User Manual for Tools Universal-air-tools UT5766. Universal Air Tools UT5766 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Universal-air-tools UT5766