Universal-air-tools UT8740C14 - 5 M14 User Manual download pdf

Read these instructions carefully before installing, operating,

servicing or repairing this tool. Keep these instructions in a safe

accessible place.

Important

Operator Instructions

Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,

Dismantling, Assembly and Safety Rules

Manufacturer/Supplier Product Type

RPM

Cycles Per Min

Universal Air Tool Company Limited

Unit 8

Lane End Industrial Park

High Wycombe

Bucks

HP14 3BY

Tel No Fax No(01494) 883300 (01494) 883237

Model No/Nos Serial No

Product Nett Weight

lbs

Recommended Use Of

Balancer Or Support

Recommended Hose Bore

Size - Minimum

Recommended Max.

Hose Length

Ins M/M Ft M

Foreseen Use of Tool

This right angle grinder is designed to be used with reinforced resin

bonded depressed centre grinding wheels that have a permitted

rotational speed in excess of 10,000 RPM. See parts lists for details of

available wheel sizes.

The tool is designed to be used for light grinding and dressing of welds,

etc. but not for cutting off. The grinder must never be used if a wheel

guard (disc cover) is not fitted.

Putting Into Service

Air Supply

Use a clean lubricated air supply that will

give a measured air pressure at the tool of

90 p.s.i./6.3 bar when the tool is running

with the trigger/lever fully depressed. Use

recommended hose size and length. It is

recommended that the tool is connected to

the air supply as shown in figure 1. Do not

connect the tool to the air line system

without incorporating an easy to reach and

Work Stations

The tool should only be used as a hand held hand operated tool. It is

always recommended that the tool is used when standing on a solid

floor. It can be used in other positions but before any such use the

operator must be in a secure position having a firm grip and footing and

be aware of the safety rules to be obeyed when using the grinder.

Angle Grinder

UT8740A10 - 4” M10

UT8740A14 - 4” M14

UT8740B14 - 4 1/2” M14

UT8740C14 - 5” M14

10,000

3/8 10 30 10

4.4

2.0

Page No 1

Noise Level Sound Pressure Level 83.0 dB(A)

Test Method Tested in accordance with Pneurop

test code PN8NTC1

Vibration Level

Test Method Tested in accordance with ISO

standard 8662

1.2

Metres / Sec²

Air Pressure

Recommended Working

6.3

bar

PSI

Recommended Minimum

n/a

bar

n/a

PSI

Maximum

7.0

bar

100

PSI

Personal Safety Equipment

Use - Safety Glasses

Yes

Use - Safety Gloves

Yes

Use - Safety Boots

Use - Breathing Masks

Yes

Use - Ear Protectors

Yes

operate air shut off valve. The air supply should be lubricated. It is

strongly recommended that an air filter, regulator, lubricator (FRL) is

used as shown in Figure 1 as this will supply clean, lubricated air at

the correct pressure to the tool. Details of such equipment can be

obtained from your supplier. If such equipment is not used then the

tool should be lubricated by shutting off the air supply to the tool,

depressurising the line by pressing the trigger on the tool.

Disconnect the air line and pour into the intake bushing a

teaspoonful (5ml) of a suitable pneumatic motor lubricating oil

preferably incorporating a rust inhibitor. Reconnect tool to air supply

and run tool slowly for a few seconds to allow air to circulate the oil.

If tool is used frequently lubricate on daily basis and if tool starts to

slow or lose power.

It is recommended that the air pressure at the tool whilst the tool is

running is 90 p.s.i./6.3 bar. The tool can run at lower and higher

pressures with the maximum permitted working air pressure of

100 p.s.i./7 bar.

1 2 3 4

Summary of Contents

Page 1 - Air Supply

Read these instructions carefully before installing, operating,servicing or repairing this tool. Keep these instructions in a safeaccessible place.Imp

Page 2 - Safety Rules For A Grinder

OperatingWith the grinder correctly connected to the air supply, check the speedof the grinder with an inlet pressure of 100 psi/7.0 bar measured at t

Page 3 - Angle Grinders

Page No 3Apr 2012 Ver 1.00Ref No Part No Description1 8740A-01 Motor Housing2 8740A-02 Spring Pin3 8740A-03 Air Inlet4 8740A-04 Throttle Lever5 8740A

Page 4

DistributorNotesPage No 4This document may not be copied wholly or in part by anyone without the consent of the Directors of Universal Air Tool Compan

Comments to this Manuals

No comments

Universal-air-tools UT8740C14 - 5 M14 User Manual

Browse online or download User Manual for Tools Universal-air-tools UT8740C14 - 5 M14. Universal Air Tools UT8740C14 - 5 M14 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Universal-air-tools UT8740C14 - 5 M14