Universal-air-tools UT8735 User Manual download pdf

Manufacturer/Supplier Product Type

RPM

Cycles Per Min

Tel No

Fax No

(01494) 883300 (01494) 883237

Model No/Nos Serial No

Product Nett Weight

lbs

Recommended Use Of

Balancer Or Support

Recommended Hose Bore

Size - Minimum

Recommended Max.

Hose Length

Ins M/M Ft M

Foreseen Use Of The Tool

This die grinder is primarily designed for use with bonded abrasive

mounted point grinding wheels. It may also be used with steel rotary

files and carbide burrs provided their speed rating matches the speed of

the grinder.

This tool should not be fitted with cutting off wheels, saw blades, drill

bits, etc. If there is any doubt about the correct use of this product

contact your supplier for advice.

Also make sure that the shank size of the attachment to be driven

matches with the collet size fitted in the grinder and that the maximum

allowed running speed of the attachment exceeds that marked on the

grinder.

There are special rules governing the use of bonded abrasive mounted

point grinding wheels - for details see section "Operating".

Putting Into Service

Air Supply

Use a clean lubricated air supply that will give a measured air pressure

at the tool of 90 p.s.i./6.3 bar when the tool is running with the

lever/trigger fully depressed. Use recommended hose size and length.

It is recommended that the tool is connected to the air supply as shown

in figure 1. Do not connect the tool to the air line system without

incorporating an easy to reach and operate air shut off valve. The air

supply should be lubricated. It is strongly recommended that an air filter,

regulator, lubricator (FRL) is used as shown in Figure 1 as this will supply

clean, lubricated air at the correct pressure to the tool. Details of such

equipment can be obtained from your supplier. If such equipment is not

used then the tool should be lubricated by shutting off the air supply to

the tool, depressurising the line by pressing the lever/trigger on the tool.

Disconnect the air line and pour into the intake bushing a teaspoonful

(5ml) of a suitable pneumatic motor lubricating oil preferably

Page No 1

Extended Die Grinder

UT8735

2.73

1.24 3/8 10 30 10

22,000

Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,

Dismantling, Assembly and Safety Rules

Operator Instructions Important

Read these instructions carefully before installing, operating,

servicing or repairing this tool. Keep these instructions in a safe

accessible place.

Universal Air Tool Company Limited

Unit 8

Lane End Industrial Park

High Wycombe

Bucks

HP14 3BY

Noise Level

Sound Pressure Level 86.6 dB(A)

Test Method

Tested in accordance with Pneurop

test code PN8NTC1 and ISO Standard 3744

Sound Power Level 97.90 dB(A)

Vibration Level

Test Method

Tested in accordance with ISO

standard 8662/1 & 8662/13

Less than 2.5

Metres / Sec²

Work Stations

The tool should only be used as a

handheld hand operated tool. It is

always recommended that the

tool is used when standing on the

solid floor. It can be used in other

positions but before any such use,

the operator must be in a secure

position having a firm grip and

footing and be aware of the extra

safety precautions that must be

observed when using Grinding

Machines.

Air Pressure

Recommended Working

6.3

bar

PSI

Recommended Minimum

n/a

bar

n/a

PSI

Maximum

7.0

bar

100

PSI

Personal Safety Equipment

Use - Safety Glasses

Yes

Use - Safety Gloves

Yes

Use - Safety Boots

Use - Breathing Masks

Yes

Use - Ear Protectors

Yes

1 2 3 4

Summary of Contents

Page 1 - Work Stations

Manufacturer/Supplier Product TypeRPMCycles Per MinTel NoFax No(01494) 883300 (01494) 883237Model No/Nos Serial NoProduct Nett WeightlbsKgRecommended

Page 2 - Reassembly

OperatingSelect a suitable mounted point that has a free running speed higherthan the maximum running speed marked on the tool. Make sure thatthe diam

Page 3 - UT8735 Extended Die Grinder

UT8735 Extended Die GrinderPage No 3Dec 2006 Ver 1.30Ref No Part No Description1 731752 Motor Housing2 731759 Cylinder3 731760 Rotor4 731757 Rear End

Page 4

DistributorNotesPage No 4AccessoriesDeclaration of ConformityUniversal Air Tool Company LimitedUnit 8, Lane End Industrial Park, High Wycombe, Bucks,

Comments to this Manuals

No comments

Universal-air-tools UT8735 User Manual

Browse online or download User Manual for Tools Universal-air-tools UT8735. Universal Air Tools UT8735 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Universal-air-tools UT8735