Universal-air-tools UT8905 User Manual download pdf

Manufacturer/Supplier Product Type

RPM

Cycles Per Min

Tel No

Fax No

(01494) 883300

(01494) 883237

Model No/Nos Serial No

Product Nett Weight Recommended Use Of

Balancer Or Support

Recommended Hose Bore

Size - Minimum

Recommended Max.

Hose Length

Ins M/M Ft M

Foreseen Use

These screwdrivers are designed for the tightening and loosening of

threaded fasteners within the range as specified by the manufacturer.

They should only be used in conjunction with 1/4" male hex shank

screwdriver bits and fastener drivers.

Do not use the tool for any other purpose than that specified without

consulting the manufacturer or his authorised representative.

Putting Into Service

Air Supply

Use a clean lubricated air supply that will give a measured air pressure

at the tool of 90 p.s.i./6.3 bar when the tool is running with the trigger

fully depressed. Use recommended hose size and length. It is

recommended that the tool is connected to the air supply as shown in

figure 1. Do not connect the tool to the air line system without

incorporating an easy to reach and operate air shut off valve. The air

supply should be lubricated. It is strongly recommended that an air filter,

regulator, lubricator (FRL) is used as shown in Figure 1 as this will supply

clean, lubricated air at the correct pressure to the tool. Details of such

equipment can be obtained from your supplier. If such equipment is not

used then the tool should be lubricated by shutting off the air supply to

the tool, depressurising the line by pressing the trigger on the tool.

Disconnect the air line and pour into the intake bushing a teaspoonful

Work Stations

The tool should only be used as a hand held, hand operated tool. It is

always recommended that the tool is used when standing on a solid

floor. It can be used in other positions, but before any such use the oper-

ator must be in a secure position having a firm grip and footing. The

operator must adopt a firm grip sufficient to resist the torque reaction of

the tool, i.e. the tool will try

to turn in the hand. The op-

erator must also be aware

that when loosening fasten-

ers, the tool can move quite

quickly away from the fas-

tener being undone. An al-

lowance must be made for

this rearward movement to

avoid hand entrapment.

The operator must also

make allowance that if the

tool does turn in the hand,

the hand is not trapped

against any rigid object.

Page No 1

Straight Push Start-Auto

Shut Off Screwdriver

UT8905

3/8 10 30 10

1,000

Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,

Dismantling, Assembly and Safety Rules

Operator Instructions Important

Read these instructions carefully before installing, operating,

servicing or repairing this tool. Keep these instructions in a safe

accessible place.

Universal Air Tool Company Limited

Unit 8

Lane End Industrial Park

High Wycombe

Bucks

HP14 3BY

lbs

0.95

0.43

Noise Level

Sound Pressure Level 68.0 dB(A)

Test Method

Tested in accordance with Pneurop

test code PN8NTC1 and ISO Standard 3744

Vibration Level

Test Method

Tested in accordance with ISO

standards 8662 Parts1 & 7

Less than 2.5

Metres / Sec²

Personal Safety Equipment

Use - Safety Glasses

Yes

Use - Safety Gloves

Use - Safety Boots

Use - Breathing Masks

Use - Ear Protectors

Air Pressure

Recommended Working

6.3

bar

PSI

Recommended Minimum

n/a

bar

n/a

PSI

Maximum

7.0

bar

100

PSI

1 2 3 4

Summary of Contents

Page 1 - Work Stations

Manufacturer/Supplier Product TypeRPMCycles Per MinTel NoFax No(01494) 883300(01494) 883237Model No/Nos Serial NoProduct Nett Weight Recommended Use O

Page 2 - Reassembly

OperatingSelect the correct screwdriver bit or fastener driver to suit the screw orfastener to be tightened or loosened. Insert appropriate drive bit.

Page 3 - Ref No Part No Description

UT8905Page No 3Straight Push Start-Auto Shut Off ScrewdriverAug 2006 Ver 1.10Ref No Part No Description35 2S2001 Air Inlet Bushing36 2S2103 Retainer37

Page 4

DistributorNotesPage No 4AccessoriesDeclaration of ConformityUniversal Air Tool Company LimitedUnit 8, Lane End Industrial Park, High Wycombe, Bucks,

Comments to this Manuals

No comments

Universal-air-tools UT8905 User Manual

Browse online or download User Manual for Tools Universal-air-tools UT8905. Universal Air Tools UT8905 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Universal-air-tools UT8905