Universal-air-tools UT5825S User Manual download pdf

Manufacturer/Supplier Product Type

RPM

Cycles Per Min

Tel No Fax No(01494) 883300 (01494) 883237

Model No/Nos Serial No

Product Nett Weight Recommended Use Of

Balancer Or Support

Recommended Hose Bore

Size - Minimum

Recommended Max.

Hose Length

Ins M/M Ft M

Foreseen Use

These screwdrivers are designed for the tightening and loosening of

threaded fasteners within the range as specified by the manufacturer.

They should only be used in conjunction with 1/4" male hex shank

screwdriver bits and fastener drivers.

Do not use the tool for any other purpose than that specified without

consulting the manufacturer or his authorised representative.

Putting Into Service

Air Supply

Use a clean lubricated air supply that will give a measured air pressure

at the tool of 90 p.s.i./6.3 bar when the tool is running with the trigger

fully depressed. Use recommended hose size and length. It is

recommended that the tool is connected to the air supply as shown

in figure 1. Do not connect the tool to the air line system without

incorporating an easy to reach and operate air shut off valve. The air

supply should be lubricated. It is strongly recommended that an air

filter, regulator, lubricator (FRL) is used as shown in Figure 1 as this will

supply clean, lubricated air at the correct pressure to the tool. Details

of such equipment can be obtained from your supplier. If such

equipment is not used then the tool should be lubricated by shutting

off the air supply to the tool, depressurising the line by pressing the

trigger on the tool. Disconnect the air line and pour into the intake

bushing a teaspoonful (5ml) of a suitable pneumatic motor lubricating

Work Stations

The tool should only be used as a hand held, hand operated tool. It is

always recommended that the tool is used when standing on a solid

floor. It can be used in other positions, but before any such use the

operator must be in a secure position having a firm grip and footing.

The operator must adopt a firm grip sufficient to resist the torque

reaction of the tool, i.e. the tool will try to turn in the hand. The

operator must also be aware that when loosening fasteners, the tool

can move quite

quickly away from the

fastener being un-

done. An allowance

must be made for this

rearward movement

to avoid hand entrap-

ment. The operator

must also make al-

lowance that if the tool

does turn in the hand,

the hand is not

trapped against any

rigid object.

Air Pressure

Recommended Working 6.3 bar 90 PSI

Recommended Minimum n/a bar n/a PSI

Maximum 7.0 bar 100 PSI

Personal Safety Equipment

Use - Safety Glasses

Yes

Use - Safety Gloves

Use - Safety Boots

Use - Breathing Masks

Use - Ear Protectors

Page No 1

Direct Drive Stall Torque

Screwdriver

UT5825-S

3/8 10 30 10

2,000

Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,

Dismantling, Assembly and Safety Rules

Operator Instructions Important

Read these instructions carefully before installing, operating,

servicing or repairing this tool. Keep these instructions in a safe

accessible place.

Universal Air Tool Company Limited

Unit 8

Lane End Industrial Park

High Wycombe

Bucks

HP14 3BY

lbs

1.98

0.9

Vibration Level

Test Method Tested in accordance with ISO

standard 8662 Parts 1 & 7

Less than 2.5

Noise Level Sound Pressure Level 91.0 dB(A)

Test Method Tested in accordance with Pneurop

test code PN8NTC1 and ISO Standard 3744

Sound Power Level 102.0 dB(A)

Metres / Sec²

1 2 3 4

Summary of Contents

Page 1 - Work Stations

Manufacturer/Supplier Product TypeRPMCycles Per MinTel No Fax No(01494) 883300 (01494) 883237Model No/Nos Serial NoProduct Nett Weight Recommended Use

Page 2 - Reassembly

Safety Rules For A Screwdriver1) Read all the instructions before using this tool. All operators must befully trained in its use and aware of these sa

Page 3 - UT5825-S

UT5825-SPage No 3Direct Drive Stall Torque ScrewdriverRef No Part No Description1 99005 Slip Chuck3 6120003 Gear Housing5 6120005 Ball Bearing (2)6 61

Page 4

DistributorNotesPage No 4AccessoriesDeclaration of ConformityUniversal Air Tool Company LimitedUnit 8, Lane End Industrial Park, High Wycombe, Bucks,

Comments to this Manuals

No comments

Universal-air-tools UT5825S User Manual

Browse online or download User Manual for Tools Universal-air-tools UT5825S. Universal Air Tools UT5825S User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Universal-air-tools UT5825S