Universal-air-tools UT8011R - 1/2 User Manual
Browse online or download User Manual for Tools Universal-air-tools UT8011R - 1/2. Universal Air Tools UT8011R - 1/2 User Manual
- Page / 4
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
Important
Operator Instructions
Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,
Dismantling, Assembly and Safety Rules
Manufacturer/Supplier Product Type
RPM
Cycles Per Min
Universal Air Tool Company Limited
Unit 8
Lane End Industrial Park
High Wycombe
Bucks
HP14 3BY
Tel No Fax No(01494) 883300 (01494) 883237
Model No/Nos Serial No
Product Nett Weight
lbs
Kg
Recommended Use Of
Balancer Or Support
Recommended Hose Bore
Size - Minimum
Recommended Max.
Hose Length
Ins M/M Ft M
Foreseen Use Of The Tool
The tool is designed to be used only for the purpose of driving,
tightening and loosening of threaded fasteners, usually nuts and bolts,
when fitted with a suitable drive socket.
It is allowed to use suitable extension bars, universal joints and socket
adaptors between the square output drive of the ratchet wrench and
the female square drive of the socket.
Do not use the tool for any other purpose than that specified without
consulting the manufacturer or the manufacturer's authorised supplier.
To do so may be dangerous.
Never use the ratchet wrench as a hammer to dislodge or straighten
cross threaded fasteners. Never attempt to modify the tool for other
uses and never modify the tool even to be used as a ratchet wrench.
Putting Into Service
Air Supply
Use a clean lubricated air supply that will give a measured air pressure
at the tool of 90 p.s.i./6.3 bar when the tool is running with the trigger
fully depressed. Use recommended hose size and length. It is
recommended that the tool is connected to the air supply as shown in
figure 1. Do not connect the tool to the air line system without
incorporating an easy to reach and operate air shut off valve. The air
supply should be lubricated. It is strongly recommended that an air filter,
regulator, lubricator (FRL) is used as shown in Figure 1 as this will supply
clean, lubricated air at the correct pressure to the tool. Details of such
equipment can be obtained from your supplier. If such equipment is not
used then the tool should be lubricated by shutting off the air supply to
the tool, depressurising the line by pressing the trigger on the tool.
Disconnect the air line and pour into the intake bushing a teaspoonful
(5ml) of a suitable pneumatic motor lubricating oil preferably
incorporating a rust inhibitor. Reconnect tool to air supply and run tool
slowly for a few seconds to allow air to circulate the oil. If tool is used
frequently lubricate on daily basis and if tool starts to slow or lose power.
Work Stations
The tool should only be used as a handheld hand operated tool. It is
always recommended that the tool is used when standing on the solid
floor. It can be used in other positions but before any such use, the oper-
ator must be in a secure position having a firm grip and footing and be
aware that when loosening fasteners the tool
can move quite quickly away from the fastener
being undone. An allowance must always be
made for this rearward movement so as to
avoid the possibility of hand/arm/body en-
trapment.
Ratchet Wrench
Reactionless Series
UT8001R - 3/8”
UT8011R - 1/2”
400
3/8 10 30 10
No
2.82
1.28
Page No 1
Noise Level Sound Pressure Level 90.0 dB(A)
Test Method Tested in accordance with Pneurop
test code PN8NTC1
Vibration Level
Test Method Tested in accordance with ISO
standard 8662
15.3
Metres / Sec²
Air Pressure
Recommended Working
6.3
bar
90
PSI
Recommended Minimum
n/a
bar
n/a
PSI
Maximum
7.0
bar
100
PSI
Personal Safety Equipment
Use - Safety Glasses
Yes
Use - Safety Gloves
Use - Safety Boots
Use - Breathing Masks
Use - Ear Protectors
Yes
Summary of Contents
Page 1 - Cycles Per Min
Read these instructions carefully before installing, operating,servicing or repairing this tool. Keep these instructions in a safeaccessible place.Imp
Page 2 - Tool Maintenance
OperatingFit securely to the tool the socket or attachment required to perform theoperation. Ensure that the reverse button situated on the opposite s
Page 3 - For 1/2” UT8011R
UT8001R 3/8" Ratchet WrenchUT8011R 1/2" Ratchet WrenchPage No 3Apr 2012 Ver 1.00Ref No Part No Description1 8001R-01 Housing2 8001R-02
Page 4
DistributorNotesPage No 4This document may not be copied wholly or in part by anyone without the consent of the Directors of Universal Air Tool Compan
Related products and manuals for Tools Universal-air-tools UT8011R - 1/2
(4 pages)© 2020, manymanuals.com. All rights reserved. | 2.734 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals