Universal-air-tools UT8795-DC User Manual
Browse online or download User Manual for Tools Universal-air-tools UT8795-DC. Universal Air Tools UT8795-DC User Manual
- Page / 4
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
UT8795 UT8795-DC
2.64 2.70 lbs
1.20 1.23 Kg
Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
ImportantOperator Instructions
Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,
Dismantling, Assembly and Safety Rules
and length. It is recommended that the tool is connected to the air
supply as shown in figure 1. Do not connect the tool to the air line
system without incorporating an easy to reach and operate air shut off
valve. The air supply should be lubricated. It is strongly recommended
that an air filter, regulator, lubricator is used as shown in Figure 1 as this
will supply clean, lubricated air at the correct pressure to the tool.
Details of such equipment can be obtained from your supplier. If such
equipment is not used then the tool should be lubricated by shutting off
the air supply to the tool, depressurising the line by pressing the trigger
on the tool. Disconnect the air line and pour into the intake bushing a
teaspoonful (5ml) of a suitable pneumatic motor lubricating oil
preferably incorporating a rust inhibitor. Reconnect tool to air supply
and run tool slowly for a few seconds to allow air to circulate the oil. If
tool is used frequently lubricate on daily basis and if tool starts to slow or
lose power.
It is recommended that the air pressure at the tool whilst the tool is
running is 90 p.s.i. The tool can run at lower and higher pressures with
the maximum permitted working air pressure of 100 p.s.i.
Manufacturer/Supplier Product Type
RPM
Cycles Per Min
Model No/Nos Serial No
Product Nett Weight Recommended Use Of
Balancer Or Support
Recommended Hose Bore
Size - Minimum
Recommended Max.
Hose Length
Ins M/M Ft M
No
Page No 1
Orbital Block Sander
UT8795
UT8795-DC Central Vac
Pad Size 180mm x 110mm
3/8 10 30 10
8,500
Universal Air Tool Company Limited
Unit 8
Lane End Industrial Park
High Wycombe
Bucks
HP14 3BY
Work Stations
The tool should only be used as a hand held hand operated tool. It is
always recommended that the tool is used when standing on a solid
floor. It can be used in other positions but before any such use the
operator must be in a secure position having
a firm grip and footing and be aware of the
safety rules to be obeyed when using the
sander.
Foreseen Use of the Tool
This tool is designed for the purpose of cleaning or sanding a variety of
basically flat materials. The orbital action reduces the amount of
abrasive grinding marks and hence is primarily a finishing sanding tool. It
can be used with a variety of grades of abrasive paper which is held in
position by two clamps. The tool has alternative velcro fastening which
does not require use of the paper clamps.
It can be used in conjunction with water if this is a requirement for
improved finishing, to reduce dust or with wet/dry abrasive paper. Do
not use the tool for any other purpose than that for which it was
designed. Do not modify the tool for any other use or for its use as a
sander without first consulting the manufacturer.
Putting Into Service
Air Supply
Use a clean lubricated air supply that will give
a measured air pressure at the tool of 90 p.s.i.
when the tool is running with the lever fully
depressed. Use recommended hose size
Tel No
Fax No
(01494) 883300
(01494) 883237
Noise Level
Sound Pressure Level 80.0 dB(A)
Test Method
Tested in accordance with Pneurop
test code PN8NTC1 and ISO Standard 3744
Vibration Level
Test Method
Tested in accordance with ISO
standards 8662 Parts 1 & 8
Less than 2.5
Metres / Sec²
Personal Safety Equipment
Use - Safety Glasses
Yes
Use - Safety Gloves
Use - Safety Boots
Use - Breathing Masks
Yes
Use - Ear Protectors
Air Pressure
Recommended Working
6.3
bar
90
PSI
Recommended Minimum
n/a
bar
n/a
PSI
Maximum
7.0
bar
100
PSI
Summary of Contents
Page 1 - Air Supply
UT8795 UT8795-DC2.64 2.70 lbs1.20 1.23 KgRead these instructions carefully before installing, operating,servicing or repairing this tool. Keep these i
Page 2 - Safety Rules For A Sander
Page No 2OperatingSelect a suitable abrasive sheet (see Section "Foreseen use of the tool")and make sure that it is fixed securely to the to
Page 3 - Ref No Part No Description
Page No 3UT8795 & UT8795-DC Orbital Block SanderRef No Part No Description1 UT-OB-01 Regulateor2 UT-OB-02 O-Ring (2)3 UT-OB-03 Snap Ring4 UT-OB-04
Page 4
DistributorNotesPage No 4AccessoriesDeclaration of ConformityUniversal Air Tool Company LimitedUnit 8, Lane End Industrial Park, High Wycombe, Bucks,
Related products and manuals for Tools Universal-air-tools UT8795-DC
(4 pages)© 2020, manymanuals.com. All rights reserved. | 0.713 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals